Quixx 10003 - Acrylic scratch eraser, 50g

Before buffing, clean the plastic surface thoroughly so any loose debris doesn’t further scratch the plastic. Use warm water and a few drops of dish soap, or a small amount of rubbing alcohol applied on a clean cloth or cotton round. Soak a piece of 800-grit wet/dry sandpaper in water for several minutes until saturated. Use a gentle, circular motion to sand the area, making sure not to apply too much pressure or you could introduce new scratches. Rinse between passes and re-wet the sandpaper as needed throughout the process. STEP 5: Go for a finer grit. If you want to learn how to remove scratches from acrylic, acrylic sheets or acrylic products, also commonly known as Plexiglass or Perspex, read this step by step guidance from the team of plastic experts at The Plastic People. These methods are tried, tested, and sure to provide outstanding results everytime! It’s easy to repair acrylic that has light surface scratches, which generally result from regular wear-and-tear. To begin, get a few basic items ready: House Cleaning Professionals Expert Interview. 12 July 2019. Run the cleaning cloth under warm water until it's completely saturated. Wring the cloth out so it isn't dripping wet when you use it. [7] X Research sourceTo evaluate the depth of scratches, lightly run your fingernail over the scratched portion of acrylic. If the scratch caught your fingernail, then it’s a deep scratch. If the scratch is deep, try to estimate how deep it is. Any scratches deeper than 5 mm are exceptionally heavy scratches – these are generally regarded as irreparable, and can only occasionally be repaired by specialty buffing tools.

Wet a piece of 1200 grit sandpaper, and lightly rub it into the scratched portion in a circular motion. Hold the heat gun 2–3 in (5.1–7.6 cm) from the plexiglass and turn it on. Position the plexiglass so you can easily reach the scratch with your heat gun. Keep the heat gun's nozzle at least 2 inches (5.1 cm) from the plexiglass so you don't accidentally cause it to melt or bubble. When you're ready to start, press the power button to start the machine. [13] X Research source Apply a thin layer of plexiglass polish to the area. The area with the scratches will look cloudy when you're finished buffing it with the sandpaper. Apply a coin-sized amount of plexiglass polish onto a clean cloth and work it into the glass in small circular motions. Keep buffing the polish for 30 seconds or until it turns clear on your surface. Wipe the polish off with a clean, dry cloth to remove the scratches. [5] X Research sourcea machine polisher. Despite this, it worked well with just hand application, making good improvements to the overall shine in its section. Much like Auto Finesse’s Tripple, it could not make the same inroads on the blade marks as our top two, but it did enoughto secure a top-four finish. Start by wetting some 800 grit paper. Take a piece, and fold it in thirds. This will give you a smaller surface to work with, and make it easier to hold the paper. Run some water over the sandpaper. [9] X Research source

This article was co-authored by Jon Gholian. Jon Gholian is a Cleaning Specialist and the Founder of Cleany, a home and office cleaning concierge service based in New York City, New Jersey & Miami. Cleany specializes in providing quality cleaning and handyman services to all their customers. All Cleany employees are insured, bonded, and professionally trained. Cleany has been featured in the New York Times, Bravo & Redfin. If some scratches are still visible, get the sandpaper, water, acrylic polish, and a fresh, clean cotton or microfiber cloth. Then, follow these steps: Angelwax says it can be used to remove up to 2,500-grade sanding marks. Along with the rest of the top four here, it topped the results for finish improvement, leaving a shine in stark contrast to untreated areas and most of its rivals’ attempts. It had trouble with the plastic ice scraper marks, but fared better on the fine knife line, where it only had to give best to ValetPRO. A competitive price was enough to give it a narrow victory over the similar Advanced Compound.Apply a coin-sized amount of scratch remover onto your rag. Acrylic scratch removers, such as Novus or Turtle Wax, help polish your plexiglass and buff out any light scratches on its surface. Squeeze a dime-sized amount onto the damp cloth, and rub it into the cloth to spread it. If you have multiple scratches you need to remove, use a quarter-sized amount instead. [9] X Research source Follow these handy tips from plastic product providers The Plastic People, and your acrylic or products made from it will continue to shine.Light scratches, as you can imagine, are much easier to combat than deep ones.