Parrot MKi9200 Hands-Free Car Kit

Product Information

Play some music form the Parrot (any source) and turn the Parrot volume to about 80 % and then set level through Audi headunit. Leave Parrot volume for music set to about 80% If the firmware is earlier than v1.96 you will need to update to this version first and then can go to later ones: V2.11 or V2.20 are both fine

Parrot MKi9200 (English - 30 pages) User manual Parrot MKi9200 (English - 30 pages)

From your description this would point to a power supply issue or a faulty MKi9200. To diagnose further you will need a multimeter.Apple iOS users are recommended to do the following – revert to IOS 9 ( if only, as this would cure the issue – sadly Apple do not allow this…)

Parrot MKi-9200 Bluetooth carkit with USB/AUX input [Parrot Parrot MKi-9200 Bluetooth carkit with USB/AUX input [Parrot

Any idea what can i do to solve this? I have understood that parrot is not involved in hands free development anymore, but this is a dissaster….The MKi automatically synchronize the names and phone numbers in your mobile with their phonebooks and update theirs phonebooks each time a new entry is detected. The MKi series offer the widest compatibility with existing and future Bluetooth mobile phones, thanks to its full compatibility with the Bluetooth wireless communication protocol. why to install the latest firmware 2.20 is it necessary to put version 1.96 first if it has an older version? Hello, I have a problem where I put a usb drive, and select a song from the folders, however the car does not react and the song does not start as the Parrot is showing that the song is playing. I have a Parrot MKI9200 and audi a4 b7. Also I can make calls trough the speakers when conected with my phone, however when I try to put audio trough bluetooth, same issue. No sound, no nothing..

Parrot MKi Car Kit downloads | Parrot Support Center Parrot MKi Car Kit downloads | Parrot Support Center

Have only ever changed 2 blown fuses on any Parrot kit – they just don’t blow (except for a good reason)Please note that if you have a control box with V1.00, V1.0.1, V1.0.2 or V1.0.3 the replacement screen is no longer available and you MUST NOT use a screen from the new version as the control box will destroy it. Do not bother with version 2.00 firmware as it had bad echo problems on handsfree – these should be updated to V2.11 or V2.20. The alert tones are sent by the phone and the Parrot is playing what it has been sent (as it’s supposed to do). i have mki9200 with Danish language and I want to update it to 2.2, now i have 1.96 but when i try to install the new file it says file transfer is cancelled. Can you give me the file link and what should i do in this case ? i tried seeting 1.96 again but it doesn’t work

Parrot Mki9200 Control Pad/Wireless Remote Control with Parrot Mki9200 Control Pad/Wireless Remote Control with

With power applied measure the voltage on the Red permanent 12v wire and make sure it does not go off when you turn the ignition off. If this is ok measure the voltage when playing music atlow level and then increase volume. If the voltage is between 12 and 14.5 this is normal and would point to a control box issue. Would recommend that you leave it to try to complete the update for a further 10 mins. After this period you can only try the following:If for some reason you do not have the accessory cables (USB, iPod 30 pin and Aux cable) then you cannot update the firmware. Benefits of the Update Hi, I have a Pixel 3 android device and a Parrot MKi9200. Bluetooth works just fine however when I connect the usb cable it charges for about 2 seconds but then stops and I can’t play music over Usb. Hi, i got the Parrot MKI9200 and it’s been working fine with my iPhone 7 IOS13.3.1 but now, when i connect my phone n play a song, it shows that it’s playing but no sound comes out, however, if someone was to call, it would work normally Hi there , I have a Parrot MKI9200 , everytime I play music or exit a screen from the menu the speakers make a loud pop , as if it letting you know I have exited a certain screen etc. The mic, wiring harness and ipod/usb lead stays the same ( unless it is a MK3 control box, where the ipod connector is deleted).