MEM Memera 2000 - ALB161 - 16a Type B Single Pole MCB

Product Information

Delta decided to keep the brands MEM and Bill separate until 1998 when they finally phased out the Bill brand. What most people don't realise is that all the products that were manufactured were identical in both brands. Delta manufactured the products and either labelled them MEM or Bill. Qwikline II -This range superseded the original Qwikline but the range was not as broad with only types B & C available and a breaking capacity of 6kA. These only come as single pole. Later versions were branded as Schneider but are identical to the Square D. They will also fit Loadcentre boards. For the person who asked about Smartmeter, yes one fitted in last year and quite close to CU (2 meters?). Though similar episode of nuisance tripping preceded its installation and went away of its own. What are you thinking about this? Loadcentre – This was a new range introduced by Schneider but using the brand name of Square D. This is more of a commercial range with types B,C & D available (B type only in single pole). They have a breaking capacity of 10kA and. Later versions were branded as Schneider but are identical to the Square D. These will also fit the Qwikline II boards.

Fortunately the situation with Bill and MEM MCCB's is not as confusing. Firstly MCCB's are made to a different standard to MCB's, BS60947-2. Whilst that standard has been updated to allow for new technologies it still remains as the current British Standard. Memshield 2 – These are also a commercial breaker and come in types B,C & D. These also will fit into all Memera 2000 range boards. Memshield 1 – These are a commercial breaker and come in various types (Type 2,3,B,C & D) depending upon the age. Most are M9 rated. Memera 2000AD – These have a narrow terminal and only fit boards specifically marked Memera 2000AD. They won't fit in older boards.The Polestar range of breakers was unique because they had a higher than usual fault rating of 16kA where standard breakers at the time were 6kA and 9kA. What this meant was that Polestar could be used in areas where a high kA was required without having to use Moulded Case Breakers (MCCB's) or HRC fuse carriers. Crabtree Polestar breakers are also unique in that they are much wider (25mm) than a standard mcb (18mm). This extra width was needed for the bigger arc splitter to allow for a higher kA rating. but mounted above the old Wylex fuse boxes, however done before the rules changed as to electrical equipment in the control of an ordinary person. But still today we have isolators before the CU to comply with HSE rules an live working, so not sure if we can still mount SPD or RCD in separate box before or after main CU? Bill Switchgear was probably one the oldest British electrical brands and was especially known for bigger switching devices like triple pole fuse switches and switch fuses and LV panelboards. The company was aquired by Delta in 1973 who also owned another well known brand, MEM. So question one does it pass when tested with a RCD tester? If so what makes you think it is faulty? I am sure the one in my old house was tripping due to surges when a neighbour was welding. Two identical RCD's would hold for 18 months without a problem, then trip for seeming no reason for couple of weeks, then again two years no tripping. All MCCB's in MEM's Memshield 2 range or Bill's Talisman Plus range are branded as such. Even though Eaton bought out Delta in 2003 they maintained the old branding until they came out with the latest range, Memshield 3. Even though they are using the Memshield brand all breakers are now marked as Eaton. Still Confused?

In the late 1980's Crabtree were looking to replace the outdated (but still widely used) C50 range. What they came up with was the Polestar range and it was a great success in commercial and industrial applications. Not all pods are the same, some have long leads for triple pole boards and some have short leads for use in domestic boards. Also worth mentioning that the pods will fit the Memera 2000 range of MCB's as well but only the part numbers that start ALB or ALC. After 1994 the British Standard of BS60898 came into effect and the range was changed to Types B, C & D and now included double pole mcb's as well. RCBO's were now being widely used and theses were available in Types B & C although it's rare to see Type B in use as most installations were commercial. Square D was bought out by Schneider in 1991 and although they changed the appearance of the circuit breakers the later versions will still fit the older boards. Confused? Well it gets worse because by the time that Delta/Eaton decided that they needed to manufacturer some of the older products to keep the peace with customers the British Standard BS3871 had changed. Previously all MCB's had been marked with a ‘Type' (either 1,2,3 or 4) but BS3871 had changed so that Type 1 MCB's were no longer used and Types 2,3 & 4 were now Types B,C & D.Memera 2000 – There are several different styles of MCB's in this range but all will fit any Memera 2000 board. So now you have a range of circuit breakers that are either branded MEM,Delta,Bill or Eaton. They may me marked either Type 2,3,4 or Type B,C,D. Some have a printed wrap around label and some have silk screen printing direct on the MCB. You can also buy MCB's pre-fitted with a pod in both the Memshield 2 and Memera 2000 ranges. These are usually just the 30mA size but field fit versions are availble is the following sizes: MEM first started manufacturing circuit breakers in 1965 and were one of the UK's biggest names in circuit protection. Now they go under the trade name of Eaton but still use the MEM name on some products. As with MCB's all MCCB's were manufactured by Delta and either branded MEM or Bill. They are identical apart from the logo and and a slight difference in the part number. You won't find any branded Delta, they never used that branding on any moulded case breakers.