Joined in 2023 
82 
63 About this deal
It depends on the input voltage and current, the amount of the maximum stable output current is produced. These DC-DC boost converter modules operate at the frequency ≥1.2MHz, the typical efficiency is 93% subjected to the withdrawn load current.
DC DC Converters | Electronic Components Distributor DigiKey
If you want your 5V ARGB devices to act like 5V ARGB devices (multiple colors at the same time) you will need an ARGB signal coming from somewhere. Many controllers can get their ARGB signals from USB 2.0 headers and third party software instead of a dedicated header and motherboard software (Such as Corsair or NZXT, but I dont know of any brands that work with standard ARGB equipment off the top of my head.) As I said, not an electronic engineer, hence my beginer questions… As a general rule, it seems that each IC is asking for input/decoupeling capacitor on 5V/VCC, is it ok to not put all these caps and reduce component load? I am trying to design a tiny PCB to repair some equipement (hence the tiny PCB, it HAS to fit in the existing housing), and I need to put a 5V to 12V booster to power a 2W stepper motor (3.5V*0.6A) through a A4988 stepper driver (Althrough, typically, the draw is only around 1.5W).The output source impedances are typically 150Ω, providing useful output currents up to 10mA. The low quiescent current and high efficiency make this device suitable for a variety of applications that need both positive and negative voltages generated from a single supply.
Converter 5V to 12V 10A 120W Boost Power DC to DC Step Up Converter 5V to 12V 10A 120W Boost Power
This USB 5v to 12v converter is most useful for powering up the WiFi router and decorative LED strip. The LT1173 consumes just 110µA supply current at standby, making it ideal for applications where low quiescent current is important. The device can deliver 5V at 80mA from a 3V input in step-up mode or 5V at 200mA from a 12V input in step-down mode. isolation if you plan to power a device which is somehow connected to the mains as well. That way you wont fry your computer if your computer and the device are not on the same phase.So I got a converter, the deepcool. Thing is, it only converts 1 5v3pins into 12v for the motherboard, but I have multiple ARGB components shipped already (RGB Fan hub, RGB HSF, RGB m.2 heatsink, RGB Gpu support). The LT1173 is a versatile micropower DC-DC converter. The device requires only three external components to deliver a fixed output of 5V or 12V. Supply voltage ranges from 2.0V to 12V in step-up mode and to 30V in step-down mode. The LT1173 functions equally well in step-up, step-down or inverting applications.
RGB convertor - DeepCool RGB convertor - DeepCool
This design has a 22µF “output” capacitor. But I already have a 100µF capacitor as an “entry” to the A4988 stepper. PCB space is VERY limited for me. Can I just use the 100µF and drop the 22? I have shared my project on easyEda at: https://easyeda.com/editor#project_id=9220fa26c27845ae8d1bbd93b3a543d9 regulation to make sure the output stays at 12V as long as the load consumption stays within the specs. In this post we will be avoiding using the old school method and only focus on boost converters with simple ICs. Earlier methods or you can say older methods used transistors as a switching device externally and lots of components were required to implement it making it complex. That is the reason to go with ICs and modules. Also it will save a lot of time to center your attention towards the actual functioning of the project rather than the power supply.
This circuit is similar to the above except output voltage in the circuit can be adjusted. As I already mentioned that output voltage is set by means of Voltage fed into the FB pin of MT3608. Here I have replaced the resistor R1 with Potentiometer PR1. As the resistance of POT changes the voltage in to the FB pin changes which in turn will change the output voltage accordingly. Soft start function (reduces current ripple and spikes during start-up, by limiting the initial current flow). In-built oscillator with 52KHz frequency with power conversion efficiency up to 92%, higher the output voltage higher is the efficiency. Are you in search of a reliable and high performance but simple 5v to 12v boost converter circuit? So here, in this comprehensive post, we have provided an insight of DC to DC Boost Converter & Modules, its schematic circuits, datasheet, pinout, features, and intended applications.
usb - How to transform 5 V into 12 V? - Electrical
Simillary to my question in 1), the 5V rail has 0.1µ, 4.7µ and 22µF capacitor, can I do the economy of at least one of these (once again, PCB space reducing)? As this is an Adjustable version of step up voltage regulator/ boost converter, we have to select the value of output voltage (here 12v) which is directly dependent on voltage determining resistors (here R5 and R6). The intended output can also be drawn out using a fixed output 12v switching IC Lm2677-12 which comes under the lm2577 series step-up voltage regulator, image for schematic circuit is shown below: You are using a 22µH inductor, which is at the high end of what the datasheet says. I started my design by copy/paste of an existing easyEda project which was with a 4.7µH… what is the difference between the 2 choices? what would you recomend I use for my design? Would you have a part number to suggest? ARGB Airgoo Computer Fan Controller Commander - Speed Adjustable 3-pin or 4-pin fan - Include Strip PC SoftwareWith the voltage boost converter module with IC Lm2577-ADJ, you can draw 12V @800mA stable DC voltage output at a wide range of input voltage levels from 3V to 40V. The LM2577 is designed with an 3.0A NPN switch, which is also equipped with a thermal and current limiting protection circuit. I was thinking of buying an ARGB Hub (5v3pin hub), and I'll have the said components connected to that - then will connect the 5v3pin hub to the Deepcool Converter > to my motherboard. For an input of 5v, the output of this IC’s can deliver a maximum of 800mA at 88% efficiency. For higher output current you have to increase the input voltage above 5 Volts. Below schematic is implemented using readily available Lm2577-ADJboost converter IC having adjustable output feature:
Great Deal 
New Comment