Drayton 25473 LP112 (Mk4) 2 Channel Programmer , White

Product Information

Lifestyle Timeswitches will automatically control your system by switching it on and off at times that suit you. The red light on the front of the timeswitch shows when it’s on. Sometimes you might need to change the way you use your central heating or hot water temporarily – perhaps due to an unusually cold day, or exceptional demand for hot water. While the Drayton Lifestyle LP112 wiring diagram appears complex, in reality it is quite simple to interpret. All the different components of the wiring diagram are labeled clearly, making it easy to identify which component is attached to which.

one for central heating and one for hot water. They allow you to switch either on or off, irrespective of the program. So if the heating is off, and you want warmth now – press Advance to switch it on, and it will stay on until the end of the next OFF period. Or if the hot water is on and you don’t need it, press Advance and it will go off until the beginning of the next ON period. G = a gravity-fed hot water system – which does not allow independent setting of heating without hot water, though hot water can be controlled alone. Press YES and you’ll see ON1, the start of your first central heating period. Adjust it in 1-minute steps using the – and + buttons. If the – and + buttons are held down, the time changes in 10-minute steps. If, after you’ve set OFF3 you want to fine-tune one or more weekdays, press SET? until you find the first day you want to adjust – then go through the procedure, altering any time you wish. Press SET? to move on to the next day. When you’ve finished, press SET? until you see ‘SET SAT SUN PROG?’. If the engineer hasn’t set your timings for you, your programmer will work with a standard program that has been set at the factory. If this doesn’t suit you, it’s very easy to change it – when you’ve read this introductory section, simply go to the section that contains your programmer model.On each side of the display there are four operating modes – one group for central heating, the other for hot water. You can change modes with immediate effect by using the appropriate SELECT button. This won’t alter the timings in your program, which you can return to by selecting TIMED. Your system will come on for up to 3 heating periods every 24hrs. ON1 starts the first one, OFF1 finishes it, and so on. Notice that on the standard program ON2 and OFF2 are set to the same time for both central heating and hot water. * This means your system won’t respond, but if you want to activate that middle period, or change any other timings – read on. Sometimes you might need to change the way you use your system temporarily – perhaps due to an exceptionally cold day. You need to set the timings in sequence – i.e. ON1, OFF1, ON2, OFF2, ON3, OFF3. If you get out of sequence, the display will flash a warning. Setting times for central heating and hot water to switch on and off can help reduce your home's energy consumption.

Use the SELECT button under the flap to change the mode. This won’t alter the timings in your program, which you can return to by selecting TIMED.If the engineer hasn’t set your timings for you, your timeswitch will work with a standard program that has been set at the factory. If this doesn’t suit you, it’s very easy to change it – when you’ve read this introductory section, simply turn to Press the YES button, and you’ll see ON1, the start of your first heating period. Adjust it in 1-minute steps using the – and + buttons. If the – and + buttons are held down, the time changes in 10-minute steps. By fully understanding the components, interpretation and importance of the Drayton Lifestyle LP112 wiring diagram, you can ensure that your home’s heating system works safely and efficiently. It is also important to follow all instructions related to the wiring diagram as it can differ between different systems. For example, some diagrams may require specialist tools such as a digital amp meter to complete the wiring process properly. If the timings haven’t been set for you, then your programmer will still be on the factory-set standard 24hr program, with central heating and hot water operating together on the same settings for every day of the week. But it’s easy to make changes – just follow the instructions.