Ubiquiti UAP-AC-HD UniFi MIMO WiFi Access Point with PoE

Product Information

hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON Pull the Ethernet cable through the Mounting Plate, and attach the Mounting Plate to the junction or outlet box using at least two screws (not included). bin_filename=QCA9984/hw.1/athwlan.bin swap_filename=/lib/firmware/QCA9984/hw.1/athwlan.codeswap.bin This is the secure version of the Unifi HD. The main difference between the two is that the SHD is designed for secure areas, like hospitals and banks. The SHD is designed with a dedicated dual-band radio to constantly monitor and protect the wireless network traffic.

We were granted DFS on February 18th (we would have been granted before official launch, on February 1st, but we had a clerical error which forced a resubmittal of some documents). So the DFS-enabled firmware is out in Beta for soaking, and will be available as a stable release probably this week.”The UniFi AP can be mounted on a wall, ceiling tile, drop ceiling T-rail (up to 40 mm), or electrical junction box. Perform the steps for the appropriate installation. Since you get to choose them individually, you might want to consider getting a few different models. If you want maximum performance in one area, you can have one Pro or HD covering that, and use AC-Lite’s or mesh APs to extend the network into less used areas. Alternatively, if you want to expand coverage in the future, you don’t need to match the AP’s you currently have. You can add any of them at any time, anywhere you need them. 802.11ac Wave 1 Vs. Wave 2 The BaseStation only offers a 5Ghz Tri-band radio, so no 2.4Ghz radio. You can choose between Small Cell and Large Cell setup, allowing you to optimize the installation for maximum coverage. We observed relatively large differences in the signal between 2.4GHz and 5GHz transmitters working in Mesh topology. At 2.4GHz the reported signal is 68dBm when the transmitter parameters are set in "auto" mode. At 5GHz the reported signal was only 86 dBm with "auto" mode settings.

In the early access store, we can also find the new Unifi 6 Mesh, which has the same design as the FlexHD and is likely going to replace the FlexHD in the near future. Read more about it in the outdoor section. UniFi In-Wall HD – UAP-IW-HD

Product Reviews

hif_completion_thread_startup: pipe_num:0 pipe_info:0xd9af4878hif_completion_thread_startup: pipe_num:3 pipe_info:0xd9af4950hif_completion_thread_startup: pipe_num:4 pipe_info:0xd9af4998 All UniFi Cloud Gateways, as of November 2023. These models are newer, and they all run UniFi OS. They have been called UniFi OS Consoles, Gateway Consoles, and now Cloud Gateways. They act as routers or firewalls, and also run the UniFi software applications like Network and Protect. These can’t be used with Cloud Keys, cloud services, or a self-hosted UniFi Network application. The only solution to force MESH topology on 5GHz frequencies in the tested environment was to set the transmitter channels rigidly on a specific frequency. You should first set up a remote transmitter that works with the rest of the network in Mesh topology, and only then connect the transmitter with an Ethernet cable to the network. After forcing one channel (100 with DFS, 80MHz) on both frequencies, after a longer period of time the device connected to 82dBm signal. The longer waiting time for the connection was forced by maintaining compatibility with DFS and Radar Detect functionality. The purpose of our tests is to verify the network coverage in Mesh topology. Both in terms of signal coverage and real speeds available in the building.

Dedicated hardware offload for QoS, Guest Control, and client management ensures high throughput and reduced latency. Unifi SDH – UAP-AC-SHD To specify which AP and which band was being used, I used the settings offered in the UniFi network controller or Instant On portal, and swapped them in and out as needed. I then stepped through the different channel widths and bands, letting the connection stabilize before beginning my tests.

T-Bar Mount

Ubiquiti offers a couple of UniFi access points that can be used outdoor. I have written a more detailed guide about the outdoor access points that you can find here. To keep all the UniFi ap comparisons in one overview I will also briefly mention them here. Ubiquiti Networks ท่านสามารถติดต่อเราได้ที่ Line Official ของเรา ที่พร้อมจะให้บริการและช่วยเหลือในทุกคำถาม hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 Write the OpenWrt sysupgrade image to the mtd partition labeled “kernel0”. Also verify the used partition device using /proc/mtd.

qdf_fs_read[54]: Fail to Open File /tmp/wifi1.caldataol_transfer_bin_file: flash cal data len 0 doesn't equal to 12064 As of the latest firmware 3.7.45.6182, which rolled out recently, DFS channels are now officially supported. This includes 5GHz channels 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 and 144.ol_ath_pci_probe num_radios=1, wifi_radios[1].sc = d90c0480 wifi_radio_type = 2 subvendor = 0x0777 subdevice = 0xe5a2 The AC-HD is the top of the line for home networks, exceeded only by the UAP-SHD and UAP-XG. It offers the best speeds UniFi offers on 2.4 GHz and 5 GHz. It also features an antenna specifically designed for close cell spacing and vertical coverage, and dedicated hardware offload for QoS, Guest Control, and Client Management. Memory: 476872K/491520K available (6261K kernel code, 196K rwdata, 1564K rodata, 1024K init, 240K bss, 14648K reserved, 0K cma-reserved, 0K highmem) The Access Point AC HD (UAP AC HD) is a high-performance, indoor/outdoor, 802.11 ac WiFi access point that utilizes Wave 2 technology to reach an impressive 2+ Gbps aggregate throughput rate with its 5 GHz (4x4 MU-MIMO) and 2.4 GHz (4x4 MIMO) bands. The UAP AC HD also has a focused antenna pattern to enhance your network's capacity and reduce interference from neighboring access points. This access point is powered with PoE+ and is equipped with (2) GbE RJ45 ports and (1) USB port to support multiple connection types. The UAP AC HD can be set up in minutes and fully managed with the UniFi Network web application or UniFi mobile app.