TWILIGHT

Product Information

This floor has an almost shabby chic look to it but don't be fooled by appearances - it's got oodles of character! Misuse - No responsibility will be accepted for any damage caused directly or indirectly through misuse, abuse, accident or use that is not consistent with the LiViTLVT installation instructions. No guarantee either express or implied is given for any damage due to inadequate care or other causes including without limitation, stains, damage caused by worn or narrow-heeled shoes, by the movement of furniture or equipment, by heavy items, by impact, by scratches or scarring caused by pets or other animals, by abrasive or sharp-pointed items, or by extreme heat.. Cleaning with this method when the floor looks dirty, or once a week, will maintain your floor adequately. 1. Brush

Improper installation - Performance of the floor is highly dependent upon proper installation. Installation must therefore be in strict accordance with the LiViTLVT installation instructions. The first and last rows should not be less than 5 cm wide, so measure the room to create a balanced layout and you will then be able to see if the first row needs to be cut to width. If the first row of panels does not need to be trimmed in width, you must remove the tongue on the side of the board that faces the wall to allow for the correct expansion gap. All flooring deliveries (boxed products and rolls of vinyl) are to roadside only - please ensure you have assistance as drivers are not insured to bring your flooring into your home. Decode": Published by WB Music Corp. (ASCAP)/But Father, I Just Want To Sing Music (ASCAP)/Josh's Music (ASCAP)/FBR Music (ASCAP), Meaux Hits/Hunterboro Music (ASCAP), Rimutaka Music Publishing (ASCAP) To cut a board, measure where to cut it and then with the decor side up, use your T-square and Stanley knife to cut into the board. You will not cut all the way through so just snap it to get a clean cut as shown.

Although your LiViT LVT floor is one of the easiest floors to maintain, please follow our recommendations below and that way you'll keep it looking fresh as well as protecting the factory finish. After installing your floor, give it an initial cleaning to get rid of any dirt or debris. Switch off or lower the underfloor heating to 15°C at least 48 hours before installation and keep it at that temperature during installation. 24 hours after installation, increase the temperature of the underfloor heating gradually by 5°C each day up to a maximum floor temperature of 27°C. Do notexceed 60W/m² with electrical underfloor heating systems .

LiViT LVT can be installed on top of concrete, tiles, wood and most existing hard-surface floor coverings provided that the subfloor is smooth, dry and clean. It should not be installed on soft-surface floor coverings such as carpet or cushion vinyl. A bit of planning, a bit of care and your floor will look as though it's been laid by a professional! Abnormal environmental conditions - LiViTLVT flooring products are guaranteed to perform in what we consider to be normal residential and commercial applications. Any exposure to excessive heat or excessive moisture may cause damage to the flooring and is not covered by this warranty regardless of cause or source. Electric under-floor heating systems are able to supply an almost instantaneous heat to the floor which warms up the floor over a very short space of time. This can cause tensions within the floor. We cannot therefore guarantee a LiViTLVT floor which is laid over electric under-floor heating.Any damage caused by environmental conditions outside the tolerances specified in the LiViTLVT installation instructions is excluded from any or all of this warranty. Don't forget to allow the same expansion gap around pipes and columns. The easiest way to drill the holes in the floor for radiator pipes is shown in the diagrams above. Line up the floor so that the header joint between two boards is in line with the pipe, join the boards together and mark where the hole should be. Drill the hole, take the boards apart and then slot them together around the pipe. You can then use a radiator pipe coverto cover up the expansion gap. LiViT LVT floors are carefully inspected by quality control personnel before leaving the factory. However, flooring should be carefully examined by the customer and the installer for any defects prior to installation. In the unlikely event of a defective board being found, it will be replaced free of charge. In the event that a defective board is installed whether inadvertently or deliberately, no warranty shall apply.Make sure you remove all traces of plaster, paint, glue, oil, grease, etc. Your subfloor must be clean, flat, dry and stable. Take up any textile floor coverings (such as carpet, needle felts, etc.) and remove all debris including nails. Where the existing skirting boards have been left in place and you've left the correct expansion gap between the skirting and the floor, you'll need the use a scotia beading to cover the gap. Before you start laying your floor or at least before you get too close to the doorway, get an offcut of the floor and the underlay, put them up against the door jamb and then use a handsaw to undercut any architraves and door linings as shown in the diagrams below. Clear out any debris from underneath so the floor can move freely under the door frame once it's installed. Once you've finished laying your floor, make sure you remove all the spacers you've used around the edge of the floor. I Caught Myself": Published by WB Music Corp. (ASCAP)/But Father, I Just Want To Sing Music (ASCAP)/Josh's Music (ASCAP)/FBR Music (ASCAP)

If for some reason you have to switch the underfloor heating off, you must carry out the above process in reverse. If the floor is exposed to lots of traffic, an acrylic emulsion polish can be used to protect the floor. LiViTLVT floors have the underlay already attached to the underside of the floor and can be laid directly onto your subfloor. No other underlay should therefore be necessary.

Write a review

If you're planning to run the floor through the doorway without a break, you will need to cut the door linings and architraves all the way round both door jambs but if you're stopping at the doorway, just cut the linings as far as you're taking the floor. Improper maintenance -Maintenance must be in strict accordance with LiViTLVT maintenance instructions. Reinstallation - In the event that we replace defective boards, we shall not be liable to provide for or incur the costs of removing or reinstalling the defective floor or resurfacing or refinishing the replaced or surrounding floor or to provide for the cost thereof unless and to the extent expressly provided in the warranty description above. No liability to replace or repair shall extend to any other materials or any other items used in the course of removal, installation or refinishing. It is vitally important to leave an expansion gap around the edge of the room and around any radiator pipes, columns or door thresholds. This expansion gap should be at least 8mm on all sides and increase 1mm for every metre over 8 metres - e.g. if the room measures 15 metres x 15 metres, the expansion gap should be 15mm.