276°
Posted 20 hours ago

Kreg KMA2685 Rip-Cut Circular Saw Guide

£9.9£99Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

As we’ve already discussed, Rip cuts are often used to reduce the width of a board or timber and create straight edges with precise measurements. So, if this is the main requirement, then rip cuts are obviously better than cross-cuts (cutting against the grain). Keep your fingers away from the path of the blade to avoid accidental cuts. Always maintain a secure grip on the saw handle.

There are a handful of ways to make it happen and with the exception of the most precise requirements (we’re looking at you, cabinetmakers), they can be accurate enough for the majority of your projects. How to Make Rip Cuts with a Circular Saw Start With an Accurate Cutline The best practice is to understand the difference between these two from our detailed comparison above and decide which one’s for you. We usually make all rip-cuts first and then move on to cross-cuts. Why? We’ll tell you in detail in the next section… Should You Rip or Crosscut First? To fully understand what a rip cut is, it’s important to also grasp its counterpart, the cross cut. While a rip cut runs parallel to the grain, a cross cut involves cutting the wood against the grain. This perpendicular motion cuts across the natural fibers, resulting in a surface that may appear rougher and less uniform compared to a rip cut.Rip cutting offers several advantages in terms of efficiency and precision. Cutting with the grain reduces resistance, making it easier to push the saw blade through the wood. This not only smoothens the cutting process but also minimizes strain on both the woodworker and the cutting tool. The resulting cut is generally cleaner and requires less sanding or additional finishing. Which is why my first suggestion is to get yourself a bandsaw! The Bandsaw in the Hand Tool Workshop Western rip saws can feel a bit like grunt work powering through a cut, whereas Japanese saws are much more about finding that rhythm (think the tortoise and the hare). Sawing with these can almost feel therapeutic.

The procedure is simple. After you made the first cut, flip the wood edge on edge to butt the same side against the fence and make a second cut. However, this only works when you resaw boards with a width less than twice the amount of maximum blade rise. A rip cut is a type of cut in woodworking that is made parallel to the grain of the wood. It involves cutting along the length of a board or piece of wood, rather than across it. This type of cut is typically used to create strips or planks of wood.

Thank you Paul for the great video, it really helped me getting started and I had great results over the last few month. Since the cut is finished in a single pass, the resulting edges are usually cleaner and straight. And finally, bandsaws are less dangerous than table saws. It’s certainly possible to make a rip cut freehand if you’re okay with being off a blade width or so either way. This takes the least amount of setup time but tends to be the least accurate. A cross-cut is a cut against the grain of the wood. After you’ve ripped the board into a smaller piece, you’ll cut it across the grain to the dimension called for in your project.

On that note, because the cut is so long, keeping it straight without a fence can be very difficult. With that being said, because you are cutting with the grain of the wood, the wood should come apart easier, and there is less of a chance of you damaging the wood when making a crosscut. Rip-cuts are easier to make in the sense that they usually don’t produce quite as much tear-out. Another consideration is that the fence only reaches so far. If you’re trying to make a rip cut 23 inches into a 48-inch wide sheet, it’s going to fall short. Clamp a Straight Edge for Rip CuttingFrom your cutline, clamp both ends of your straightedge the distance you measured between the shoe edge and blade. Slide the shoe against your straightedge and push the saw forward to make sure the blade touches your cutline. To summarize, mastering the rip cut technique is essential for woodworkers. By choosing the right saw, understanding proper techniques, and prioritizing safety, woodworkers can achieve outstanding results in their woodworking projects. Rip cuts are commonly used when you need to trim or resize a piece of wood. By following the direction of the grain, the saw blade can easily glide through the wood, removing material as required. This technique allows for greater control and accuracy in achieving the desired dimensions. Unlike other cutting methods, such as cross cuts, which we will discuss later, rip cuts maintain the wood’s inherent strength and durability. Most saws sold at big box stores are primarily intended for construction use, and while they cut well at first, they simply aren’t made to last. And for fine woodworking, you might as well be using a chainsaw instead of these cheap construction tools.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment