J-B Weld 8267UK SteelStik Epoxy Putty

Product Information

J-B Weld can be used to bond surfaces made from metal, porcelain, ceramic, glass, marble, PVC, ABS, concrete, fiberglass, wood, fabric, or paper. [7] [8] Alcohol should be avoided when cleaning surfaces, as it can degrade the bond. [9] Me and the car at the “2002: ICON” exhibit at the BMW CCA Foundation Museum in Greer, South Carolina. Rob Siegel Then, the 2002tii was accepted into an exhibit in the BMW Car Club Foundation’s museum in Greer, South Carolina, that commemorated the 50th anniversary of the BMW 2002. In February 2018, I prepared to take the car to the museum.

It hardens in 5 minutes and cures in 10 minutes. It works well under a maximum temperature of 315°C (<100 continuous). It contains 54g/l solvent. It is not suitable for soft plastic and polypropylene. VERSATILE AND DEPENDABLE: J-B Weld Original is steel reinforced, has a tensile strength of 5020 PSI and can withstand temperatures up to 550 degrees Fahrenheit (287 degrees Celsius. When fully cured, J-B Weld Original is waterproof and resistant to petroleum, chemical and acid. It is a good idea to clean the surfaces with methylated spirit or cellulose thinners and to roughen the surfaces before applying. Sampson, William (September 16, 2013). "In the Shop: Wood repair products from J-B Weld". www.fdmcdigital.com. CabinetMakerFDM . Retrieved March 27, 2015. Most epoxies add strength to a joint when the epoxy-joint layer is minimized. Epoxy, in and of itself, doesn’t carry strength. Its the cross-linking nature of the epoxy establishing bonds between the materials forming the joint. Long spans (think gaps) between the articles forming the joint creates a weak bond- the epoxy is making longer bonds to the materials to be joined. A thin gap is best. JB Weld has small metallic materials in suspension, so some gap filling will work with this original formulation.

J-B Weld is a two-part epoxy adhesive (or filler) that can withstand high-temperature environments.

J-B Kwik (stylized as J-B KWIK) is a two-part epoxy, intended as an adhesive or filler, that can withstand medium-temperature environments (up to 300°F or 149°C). [14] The epoxies tested include Gorilla epoxy, Devcon Plastic Steel, Loctite Epoxy Weld, JB Weld original, JB Weld Kwik Weld, and JB ExtremeHeat. This more or less covers the entire gamut of epoxies you would find in the glue aisle of your local home supply store; the Gorilla epoxy is your basic 5-minute epoxy that comes in a double barrel syringe, and the JB Welds are the cream of the crop. J-B Weld can be used as an adhesive, laminate, plug, filler, sealant, or electrical insulator. [8] When fully cured, J-B Weld can be drilled, formed, ground, tapped, machined, sanded, and painted. [8]The J-B Weld Company's original product line focused on a small number of products: J-B Weld (original 2-tube epoxy), J-B Kwik (4-hour epoxy), J-B Stik ( epoxy putty), Waterweld (underwater adhesive/filler), and a few others. [4] a b c d e f "Repair Products UK Ltd: Metal Glue - J-B Weld", Repair Products UK Ltd, 2009, RProducts-42. Apply the resin to both surfaces to be joined and clamp or tape the parts together until Super Steel has set hard. CURE AND SET TIME: After mixing the tubes at a 1:1 ratio, it takes 4-6 hours to set and 15-24 hours to cure. Once cured J-B Weld Original can be tapped, filled, sanded, molded and drilled. J-B Weld Original set and cure color is dark grey.

The mixture will set enough for the glued parts to be handled within 4–6 hours, [7] but requires up to 15 hours at cool temperatures to fully cure and harden. Temperatures above 50°F (10°C) shorten all these times. [7] PRODUCT FEATURES AND STRENGTH: J-B Weld WaterWeld has lap shear strength of 1300 PSI, can withstand continuous temperatures up to 300F (149C) and intermittent temperatures of 350F (176 degrees Celsius) and is chemical resistant against petroleum, hydraulic fluids and other chemicals when fully cured. CURE AND SET TIME: After kneading the two part formula together by hand, SteelStik takes 5 minutes to set and cures in 1 hour. J-B Weld SteelStik set and cure color is dark grey. But an oil leak onto the exhaust threatened to derail the trip. The leak was due to the valve cover stud in the lower left corner of the head being stripped in its hole and thus not tightening, which prevented that corner of the valve cover from sealing. This caused oil to drip directly onto the downpipe, which was a clear fire hazard. At the time, I repaired the stripped threads with a Time-Sert (helicoil). The car still appeared to be weeping a small amount of oil through the threads onto one of the exhaust studs, but this is a common problem, as the lower exhaust studs thread directly into oil runoff area on the low side of the head. I made it home without incident, and that spring I road-tripped the car 2000 more miles to other events.To use Super Steel Epoxy make sure the surfaces to be bonded are clean and dry and free from oil, dirt or grease.