Fluval FX6 High Performance Canister Filter

Product Information

Now let’s get into the troubleshooting tips. Most Common Fluval FX6 Problems and Troubleshooting Guide Startup Issues – My Fluval FX6 Will Not Start? There are various conditions and elemental factors that influence the cleaning routine of these filters. The tank owner should understand the different elements from water conditions to bio load before jotting down a cleaning schedule for their respective tank with an FX6. Your Bio Load Matters However, the appropriate time for cleaning your FX6 depends on the water conditions inside the aquarium, the fish diet you are using, and the bio load. In general, the Fluval FX6 is a very quiet filter. However, if you hear noises coming from your Fluval it may be for the following reasons; When you spend a lot of money on a piece of equipment you expect it to be flawless. However, nothing is perfect and although the FX6 canister filter from Fluval is close to perfect, it does have some common problems that don’t seem to go away.

Fluval FX6 Canister Filter Reviewed: Worth The Hype In 2023? Fluval FX6 Canister Filter Reviewed: Worth The Hype In 2023?

Hopefully, you’ve read the manual and realize that your filter is meant to turn off every 24hours to purge. Any trapped air. The only thing you have to clean now is the canister itself. You can use tap water to clean the baskets, impeller, and the canister itself. When cleaning is completed fill the canister about halfway with de-chlorinated water. The intake is Too close to air stone, filter or protein skimmer – Remove all air producing equipment to be sure they are not the reason. If they are the source of the problem try to keep the intake as far away as possible from the air source. If not possible try to create barriers between the air source and intake. The issue we are having is our tank is drilled in the bottom and has 22m hoses whilst the fx6 hoses are I Beleve 1" - along with that our inline heater and co2 atomizer need the 22m hose. Make your way through the different bio trays, and get to the bottom tray where you will find charcoal padding or any chemical media you were using depending upon your preferences. It is recommended to change these depending on their respective state. If they are too dirty or greasy, toss them in the trash and get clean replacements.As for heater and CO2 you can split the 1" pipe into two sections like below. You tweak the valve to get sufficient flow in the 16mm section. As you can see it’s very important to complete any preventative maintenance and on-going care for this expensive filter. I'm sure with that powerhouse of a filter you don't really need to worry about a few mm difference in diameter restricting flow, or damage especially since it has "Smart Pump Technology". Apart from flow rate is there any other reasons we shouldn't do this - could restricting the flow rate damage the filter for example? Foams for outer parts of trays should be cut to 37.5cm (14.75") x 9cm (3.5"). You will be able to cut 3 foams from each 17" x 11" coarse and medium foam so as this kit has 2 x coarse and 2 x medium foams that gives you enough for all 3 trays.

Fluval FX6 with 16 /22m Hose | UK Aquatic Plant Society Fluval FX6 with 16 /22m Hose | UK Aquatic Plant Society

While some tanks with FX6 may require constant maintenance, others can run for six months without any problems.We’ve tried to help out any new owners of this awesome filter, by compiling this guide to fixing the most common Fluval fx6 problems.

FX6 Canister Filter, up to 400 US Gal / 1500 L - Fluval

At the moment there's 2 plastic screw points to screw the pipes into which then connect to the tubing - infact looking at it - wouldn't surprise me if the holes are big enough once the plastic bits are off - just to work out how to get bigger pipes through and watertight! Make a template, peice of wood with same sized hole as you are drilling and silicone it in place if you can't clamp it. This stops the hole cutter slipping when you start the cut. If you wonder, “How often do you clean your FX6?” the answer, unfortunately, is that every tank is different. But if you are running carbon through your system, you should definitely be replacing that every month. Otherwise, in general, most tanks can wait for four months before going for a full FX6 cleaning session.Now, you will move on to the water exchange valve at the bottom of your canister. You will remove the exchange valve and connect the respective hose with the canister filter. This will be your entry point for eliminating all waste and refiling the canister filter with clean water. I waited four months before going for a full servicing session. However, I do keep them in good shape by doing scheduled water changes and substrate vacuuming to remove excess waste and detritus weekly. This scheduled tank maintenance helps in prolonging the filter cleaning schedule. We are really keen to just use one filter using the already drilled holes for he inlet / outlet to keep things neat and tidy. Hiya. I asked Hagen themselves as I too have an FX6 coming today for my Fluval. Here is their response:

Fluval FX6 | External Aquarium Filter | up tp 1500 L Fluval FX6 | External Aquarium Filter | up tp 1500 L

Now that you know when to clean your aquarium with an FX6 filter, it is time to learn how to clean FX6. Here are a few steps to get you started with cleaning your FX6. Other than bio load, water conditions inside the tank also help you determine the right time to clean your FX6. If the water appears to be blurry or whiteish rather than transparent, it is time to get busy and clean the tank. The absence could mean a higher bio load and foreign contaminants in your tank that need to be taken care of immediately. Crystal Clear Water Does Not Mean Optimal Water Parameters When you are cleaning sponges, make sure to put the bio media trays inside the aquarium itself. This is to preserve the beneficial bacteria in these bio-media trays while you dry off your sponges.So, all the waste in your tank falls under the category of bio load. This waste helps you determine the right time for cleaning your tank with water changes and gravel vacs and helps you set a proper cleaning schedule for your Fluval FX6 Canister. Always use a silicone lubricant after any maintenance. As you know this beast of a canister filter moves a lot of water and using the lubricant helps prevent any leaks. Use Filter Media Bags If you intend to use any media that is made up of small granular particles, be sure to place it in a bag. Loose bits can get trapped in the pump and stop your impeller from working. Replace Old Impellers Short for biological load, bio load is the waste accumulated in the water column of your tank. To better understand the bio load in your tank, here are a few examples: