Joined in 2023 
82 
63 About this deal
No, we do not recommend this as the cement is not a good conductor of heat and, due to the fixings, should not be installed directly over an insulation material either. An UFH system which is installed in the tile adhesive layer, over the board, would be OK. The benefits include easier image association with a given case, simplified new case creation, and improved data collection and accuracy. Knauf offers AQUAPANEL ®Cement Board Indoor for internal applications. However, any Knauf AQUAPANEL ®Cement Board Outdoor panels not used can be used in internal applications. Yes, as a full board, a radius of down to 3m is possible. If the board is cut into 300mm strips, then a radius of as little as 1m is achievable.
What was the previous process for entering a new case? How has including Bing Maps in the app helped? No, to be compliant to our installation requirements, please follow the standard installation guidance.A variety of factory-manufactured skylight shapes exist for sloping or flat roofs. Most include shafts (also called light wells) that can potentially exert as much influence over the energy properties as the skylight itself. Sky-lighting may also take the form of general glazed areas such as roof lights for atria, attached conservatories or sunrooms. In this form, they are less likely to be factory-manufactured and more likely to be custom-made. No, Knauf AQUAPANEL ®Floor Tile Underlay is not approved for installation in a vertical installation. New build insurance providers state that the cavity needs to be a minimum of 25mm in England and Wales, and 50mm in Scotland, Northern Ireland and Republic of Ireland. Knauf AQUAPANEL ®Cement Board Outdoor has a mass of 16kg/m². 1200mm long board is 17.28kg and 2400mm long board is 34.56kg. As the board is lightweight and only 900mm wide, it means that it can easily be worked from scaffolding, rather than having to be cut on the ground and carried to the fixing position.
No, for domestic application this is not usually needed, and due to the manner in which the Knauf AQUAPANEL ®Floor Tile Underlay is installed, the two are not compatible. Tanking over the Knauf AQUAPANEL ®Floor Tile Underlay could be considered as an alternative. No, this board should only be used for internal applications. Knauf offers Knauf AQUAPANEL ®Cement Board Outdoor (which is freeze thaw tested) for exterior uses. Many of our custom projects arise from unique architectural and aesthetic design requirements that lie outside the standard parameters of typical skylights. We have worked with thousands of architects in customized frames and extrusions for specific job requirements. The large array of projects we’ve completed offers a wealth of experience and an extensive library of completed custom designs for inspiration. Knauf recommend that the boards are installed with a 3 to 5mm gap all around the boards, and all joints are taped and jointed using Knauf AQUAPANEL ®products (this must be done for soffit applications). If the thin coat render basecoat and mesh layer is going to be applied within 4 to 6 weeks of the boards being installed, the tape and jointing application can be omitted, but the basecoat must be applied into the gaps prior to application of the basecoat and mesh layer. Wet areas such as rooms housing swimming pools, spas and saunas, wet rooms, kitchens, laundries, bathrooms, changing rooms, domestic and commercial kitchens, restaurants or anywhere where ceramic, mosaic or stone floor coverings are specified.How long can the Knauf AQUAPANEL ®Cement Board Outdoor be left exposed before I should render them? Several methods can help to decide on the size and spacing of skylights. The size of the skylight impacts its solar heat gain and its conduction gains and losses. Typically for roof windows and skylights, a 3–5 per cent floor-to-skylight area ratio is used and for some high-performing tubular skylights, 1–2 per cent is sufficient. If multiple skylights are to be used in the same room, spacing between the skylights should be 1.5 times the height of the room. We recommend you use a cement-based flexible tile adhesive (Class C2 / S1 according to EN 12004 - 12004). If you need better waterproofing than just the tiles, use a waterproof adhesive provided it is cement based.
Yes, the cladding must be ventilated at the head of the cladding with a minimum gap of 10mm between the top of the rendered cladding and the structure above (soffit box, coping etc.). This allows any warm moist air to escape from the cavity. Knauf AQUAPANEL ®Cement Board Outdoor provides a solid dry base that can withstand the extreme weathering effects of wind, rain and snow. Once taped and jointed, it can be left unfinished for up to 6 months, making use of the smallest windows of opportunity to ocmpletely close the external envelope, maximising the efficiency of the project schedule. Knauf AQUAPANEL ®Cement Board SkyLite can be used both as a ceiling in interior humid or wet environments where water vapour and high temperatures up to 70 °C occur, and as an exterior soffit, allowing the interior ceiling design theme to be continued through windows as a soffit under deep external roof overhang.Yes, where Knauf AQUAPANEL ®Cement Board SkyLite is not being sourced, Knauf AQUAPANEL ®Cement Board Indoor can be used to form a soffit system, along with the coated metal framework also offered by Knauf.
Great Deal 
New Comment